________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
________________ |
SHB102B |
|
SHB102B - Schuetzeinheit Hochvoltbatterie (18A16) |
00F0F1 |
|
Global soc 0% |
00F9EC |
|
Not able to keep main contactor closed |
00FAEC |
|
Target voltage limit reaches (during floating) |
01F9EC |
|
Not able to keep main contactor opened |
02F9EC |
|
Not able to keep contactor precharge opened |
0C200B |
|
ECU board over temperature |
10F0F2 |
|
Warning isolation monitoring value close to limit alarm (-pole) |
10F9EC |
|
Not able to open main contactor |
11F0F2 |
|
Warning isolation monitoring value close to limit alarm (+pole) |
11F9EC |
|
Not able to open precharge contactor |
12F0E1 |
|
Critical isolation monitoring value under limit alarm (-pole) |
13F0E1 |
|
Critical isolation monitoring value under limit alarm (+pole) |
20F0F1 |
|
ECU power supply undervoltage |
21F0EF |
|
ECU power supply overvoltage |
22F9E1 |
|
Voltage issue during precharge |
23F9EC |
|
Precharge error |
24F9EC |
|
Precharge cooldown |
25F9EC |
|
Not able to close main contactor |
26F9EC |
|
Not able to close precharge contactor |
28F9EC |
|
Precharge without voltage |
29F9EC |
|
No HV entering heating mode |
2AF9EC |
|
Closing error on Main contactor on Slave SHB |
2BF9EC |
|
Closing error on contactor Precharge Slave |
30F9EC |
|
CAN communication loss with BMS GW |
31F0EC |
|
CAN communication loss with HVBB2 |
31F9EC |
|
CAN communication loss with all HVBB |
32F0EC |
|
CAN communication loss with HVBB3 |
32F9EC |
|
CAN communication loss with SHB2 |
33F0EC |
|
CAN communication loss with HVBB4 |
34F0EC |
|
CAN communication loss with HVBB5 |
35F0EC |
|
CAN communication loss with HVBB6 |
36F0EC |
|
CAN communication loss with HVBB7 |
37F0EC |
|
CAN communication loss with HVBB8 |
38F0EC |
|
CAN communication loss with HVBB9 |
39F0EC |
|
CAN communication loss with HVBB10 |
3AF0EC |
|
CAN communication lost with HVBB11 |
3BF0EC |
|
CAN communication lost with HVBB12 |
3CF0EC |
|
CAN communication lost with HVBB13 |
3DF0EC |
|
CAN communication lost with HVBB14 |
3EF0EC |
|
CAN communication lost with HVBB15 |
40F0EC |
|
Voltage between (at least) 2 HVBB above limit |
40F9E4 |
|
Critical ECU power supply undervoltage alarm |
41F9E3 |
|
Critical ECU power supply overrvoltage alarm |
42F9EC |
|
Loss of power supply outside idle mode |
50F9E3 |
|
Signal HV_ENABLE out of range |
80F9EC |
|
Software safety library Error or Security module Reset |
81F9EC |
|
Software safety library Error : INIT_FAIL |
82F9EC |
|
Software safety library Error : SETUP_FAIL |
83F9EC |
|
Software safety library Error : SWITCH_PHASE_FAIL |
84F9EC |
|
Software safety library Error : ERR_INJ_FAIL |
85F9EC |
|
Software safety library Error : EARLY_PRE_RUN_TST_FAIL |
86F9EC |
|
Software safety library Error : PRE_RUN_TST_FAIL |
87F9EC |
|
Software safety library Error : RUN_TST_FAIL |
88F9EC |
|
Software safety library Error : POST_RUN_TST_FAIL |
8AF9EC |
|
HVBB adressing error (2 HVBB at the same adresse) |
8CF9EC |
|
SHB adressing issue |
91F9EC |
|
Evacuation signal coming from HVBB2 |
92F9EC |
|
Evacuation signal coming from HVBB3 |
93F9EC |
|
Evacuation signal coming from HVBB4 |
94F9EC |
|
Evacuation signal coming from HVBB5 |
95F9EC |
|
Evacuation signal coming from HVBB6 |
96F9EC |
|
Evacuation signal coming from HVBB7 |
97F9EC |
|
Evacuation signal coming from HVBB8 |
98F9EC |
|
Evacuation signal coming from HVBB9 |
99F9EC |
|
Evacuation signal coming from HVBB10 |
9AF9EC |
|
Evacuation signal coming from HVBB11 |
9BF9EC |
|
Evacuation signal coming from HVBB12 |
9CF9EC |
|
Evacuation signal coming from HVBB13 |
9DF9EC |
|
Evacuation signal coming from HVBB14 |
9EF9EC |
|
Evacuation signal coming from HVBB15 |
27F9EC |
|
HVBB problem during shutdown transition |
51F9F3 |
|
HV_ENABLE signal implausible OFF |
52F9F3 |
|
HV_ENABLE signal implausible ON |
60F9EC |
|
No HVBB available |
89F9EC |
|
Wrong HVBB adresse (Standalone) |